Radio Shack Cordless Telephone 900 MHz Digital Spread Spectrum Cordless Phone with Dual Caller ID User Guide

900 MHz Digital Spread

Spectrum Cordless Phone

with Dual Caller ID, Dual Keypad,

and Speakerphone

Important:

dures that could affect the operation of this

telephone. The telephone company notifies

you of these changes in advance, so you can

take the necessary steps to prevent interrup-

tion of your telephone service.

• Cordless phones such as this one

require AC power to operate. When the

AC power is off, you cannot dial out or

receive incoming calls using your

phone. For this reason, the phone

should not be your only telephone. To be

safe, you should also have a phone that

does not require AC power to operate

(not a cordless phone) so you can still

make and receive calls if there is an AC

power failure.

LIGHTNING

Your telephone has built-in protection circuits

to reduce the risk of damage from surges in

telephone line and power line current. These

protection circuits meet or exceed the FCC

requirements. However, lightning striking the

telephone or power lines can damage your

telephone.

• Some cordless phones operate at fre-

quencies that might cause interference

to nearby TVs and VCRs. To minimize

or prevent such interference, the base of

the cordless phone should not be placed

near or on top of a TV or VCR.

Lightning damage is not common. Neverthe-

less, if you live in an area that has severe

electrical storms, we suggest that you unplug

your phone when storms approach to reduce

the possibility of damage.

• Your cordless phone operates on stan-

dard radio frequencies, as allocated by

the FCC. Even though your phone's

access protection code prevents unau-

thorized use of your phone line, it is pos-

sible for other radio units operating on

similar frequencies within a certain area

to unintentionally intercept your conver-

sations and/or cause interference. This

possible lack of privacy can occur with

any cordless phone.

FCC STATEMENT

The phone complies with the limits for a

Class B digital device as specified in Part 15

of FCC Rules. These limits provide reason-

able protection against radio and TV interfer-

ence in a residential area. However, your

equipment might cause TV or radio interfer-

ence even when it is operating properly. To

eliminate interference, you can try one or

more of the following corrective measures:

THE FCC WANTS YOU TO

KNOW

• Reorient or relocate the receiving

antenna.

In the unlikely event that your phone causes

problems on the phone line, the phone com-

pany can temporarily discontinue your ser-

vice. If this happens, the phone company

attempts to notify you in advance. If advance

notice is not practical, the phone company

notifies you as soon as possible and advises

you of your right to file a complaint with the

FCC.

• Increase the distance between the

equipment and the radio or TV.

• Use outlets on different electrical circuits

for the equipment and the radio or TV.

Consult your local RadioShack store if the

problem still exists.

Also, the phone company can make changes

to its lines, equipment, operations, or proce-

Important Information

these openings must not be blocked or

covered. The openings should never be

blocked by placing the product on a bed,

sofa, rug, or other similar surface. This

product should never be placed near or

over a radiator or heat register. This

product should not be placed in a built-in

installation unless proper ventilation is

provided.

IMPORTANT SAFETY

INSTRUCTIONS

When using your telephone equipment, ba-

sic safety precautions should always be fol-

lowed to reduce the risk of fire, electric shock

and injury to persons, including the following:

1. Read and understand all instructions.

2. Follow all warnings and instructions

marked on the product.

12. This product should be operated only

from the type of power source indicated

on the marking label. If you are not sure

of the type of power supply to your

home, consult your local power com-

pany.

3. Never install telephone wiring during a

lightning storm.

4. Never install telephone jacks in wet

locations unless the jack is specifically

designed for wet locations.

13. Do not allow anything to rest on the

power cord. Do not locate this product

where the cord will be stepped on.

5. Never touch uninsulated telephone

wires or terminals unless the telephone

line has been disconnected at the net-

work interface.

14. Do not overload wall outlets and exten-

sion cords as this can result in a risk of

fire or electric shock.

6. Use caution when installing or modifying

telephone lines.

15. Never push objects of any kind into this

product through cabinet slots as they

may touch dangerous voltage points or

short out parts that could result in a risk

of fire or electric shock. Never spill liquid

of any kind on the product.

7. Do not fix the AC power supply cord to

building surfaces with metal fittings (If

the product has an AC power cord).

8. Unplug this product from the wall outlet

before cleaning. Do not use liquid clean-

ers or aerosol cleaners. Use a damp

cloth for cleaning.

16. To reduce the risk of electric shock, do

not disassemble this product. Take it to

a qualified serviceman when service or

repair work is required. Opening or

removing covers may expose you to

dangerous voltage or other risks. Incor-

rect reassembly can cause electric

shock when the product is subsequently

used.

9. Do not use this product near water, for

example, near a bath tub, wash bowl,

kitchen sink, or laundry tub, in a wet

basement, or near a swimming pool.

10. Do not place this product on an unstable

cart, stand, or table. The product may

fall, causing serious damage to the

product.

17. Unplug this product from the wall outlet

and refer servicing to qualified service

personnel under the following condi-

tions:

11. Slots and openings in the cabinet and

the back or bottom are provided for ven-

tilation. To protect it from overheating,

• When the power cord plug is damaged

or frayed.

Important Information

• If liquid has been spilled into the prod-

uct.

and may cause damage to the eyes or

skin. It may be toxic if swallowed.

• If the product has been exposed to rain

or water.

4. Exercise care in handling the battery

pack in order not to short it with conduct-

ing materials such as rings, bracelets,

and keys. The battery or conductor may

overheat and cause burns.

• If the product does not operate normally

by following the operating instructions.

Adjust only those controls that are cov-

ered by the operating instructions

because improper adjustment of other

controls may result in damage and will

often require extensive work by a quali-

fied technician to restore the product to

normal operation.

5. Charge the battery pack provided with or

identified for use with this product only in

accordance with the instructions and

limitations specified in this owner’s man-

ual.

6. Observe proper polarity orientation

between the battery pack and the bat-

tery charger.

• If the product has been dropped or the

cabinet has been damaged.

• If the product exhibits a distinct change

in performance.

SAVE THESE

INSTRUCTIONS

18. Avoid using a telephone (other than a

cordless type) during an electrical storm.

There may be a remote risk of electric

shock from lightning.

19. Do not use the telephone to report a gas

leak in the vicinity of the leak.

BATTERY SAFETY

INSTRUCTIONS

CAUTION: TO REDUCE THE RISK OF

FIRE OR INJURY, READ AND FOLLOW

THESE INSTRUCTIONS.

1. Use only the appropriate type and size

of battery pack specified in the instruc-

tion manual provided for this product.

2. Do not dispose of the battery pack in a

fire. The cell may explode. Check with

local codes for possible special disposal

instructions.

3. Do not open or mutilate the battery

pack. Released electrolyte is corrosive

Important Information

ˆ Contents

Features .................................................................................................................................. 8

Installation .............................................................................................................................. 9

Mounting the Phone .......................................................................................................... 9

On a Desktop ............................................................................................................. 9

On a Wall Plate or Wall ............................................................................................ 10

Connecting, Charging, and Replacing the Battery Pack ................................................. 11

Setting the Dialing Mode ................................................................................................. 12

Setting the Ringer Tone/Volume ...................................................................................... 12

Turning Auto Talk On/Off ................................................................................................. 13

Turning Caller ID/Call Waiting On/Off ............................................................................. 13

Storing Your Area Code .................................................................................................. 13

Operation .............................................................................................................................. 14

Making a Call .................................................................................................................. 14

Using the Handset ................................................................................................... 14

Using the Speakerphone ......................................................................................... 14

Receiving a Call .............................................................................................................. 14

Adjusting the Volume ...................................................................................................... 14

Selecting the Channel ..................................................................................................... 14

Using Mute ...................................................................................................................... 15

Switching Between the Handset and the Speakerphone ................................................ 15

Using Both the Handset and the Speakerphone ............................................................. 15

Using Flash ..................................................................................................................... 15

Using Redial .................................................................................................................... 15

Using Tone Services on a Pulse Line .............................................................................. 16

Using Page/Intercom ....................................................................................................... 16

Transferring a Call Between the Handset and the Base ................................................. 16

Out of Range ................................................................................................................... 17

Using a Headset .............................................................................................................. 17

Memory Dialing ............................................................................................................... 17

Storing a Name and Number in the Handset’s Memory .......................................... 17

Storing a Number in the Base .................................................................................. 19

Editing or Deleting a Number in the Handset's Memory .......................................... 19

Entering a Pause ..................................................................................................... 19

Reviewing Memory Numbers ................................................................................... 20

Dialing a Memory Number ....................................................................................... 20

Chain-Dialing Service Numbers ............................................................................... 20

Testing Stored Emergency Numbers ....................................................................... 20

Caller ID Operation ............................................................................................................... 21

Call Waiting Options Service ........................................................................................... 21

Using Call Waiting Options ...................................................................................... 21

Using Ask to Hold .................................................................................................... 22

Using Conference .................................................................................................... 22

Reviewing Caller ID Records .......................................................................................... 23

Contents

Caller ID Messages ................................................................................................. 23

Adding/Deleting the Area Code ...................................................................................... 23

Dialing Numbers from a Caller ID Record ...................................................................... 23

Storing a Caller ID Record to Memory ............................................................................ 24

Deleting Caller ID Records ............................................................................................. 24

Troubleshooting ................................................................................................................... 25

Care ................................................................................................................................ 26

Contents

ˆ Features

Headset Jack

al headset for handsfree convenience.

Your RadioShack Digital 900 MHz Dual Key-

pad Cordless Speakerphone operates on the

900 MHz band, which means less interfer-

ence, clearer sound, and greater range than

46/49 MHz cordless telephones. The Caller

ID records each caller's telephone number

(and name, if available in your area) and the

date and time of the call. If you subscribe to

Call Waiting with Caller ID service, your

phone shows you the incoming caller infor-

mation, even when you are already on the

phone.

— lets you connect an option-

Volume Controls

ume you hear through the handset and

speakerphone.

— let you adjust the vol-

Ringer Volume Control

— lets you select

from four ringer tone/volume settings or turn

it off on the handset. On the base you can

select high or low ringer, or turn the ringer

off.

Security Access-Protection Code

—helps

Your phone’s feature’s include:

prevent other cordless phone users from us-

ing your phone line while the handset is off

the base.

Dual Keypad

— let you use the keypad on

the base or on the handset to make and an-

swer calls or program the phone's features.

Long Battery Life

— the supplied battery

pack (when fully charged) provides about 6

hours of talk time or 7 days of standby time.

Speakerphone

tion handsfree from the base intercom

speaker.

— lets you hold a conversa-

Auto Talk

— you can set the phone so you

can answer a call simply by lifting the hand-

set from the base.

30-Number Memory Dialing

store 30 numbers in memory (20 in the hand-

set, 10 in the base) for easy dialing.

— lets you

Any Key Answer

— you can set the phone

so you can press any key to answer a call

when the handset is away from the base.

Caller ID Memory

ID records on the handset.

— stores up to 50 Caller

Redial

— lets you quickly redial any of the

Dual Displays

— lets you view a Caller ID

last three numbers dialed on the handset.

You can also redial the last number you di-

aled on the base.

record on the handset or base display.

Two-Way Intercom/Paging System

— lets

you send a signal from the base to the hand-

set, or from the handset to the base, to lo-

cate the handset or page someone using it

away from the base. If someone answers the

page, you can use the phone as an intercom

and speak to the person on the handset.

Hearing-Aid Compatibility

your phone with hearing aids that have a T

(telephone) switch.

— lets you use

Facedown/Faceup Handset Charging

you can charge the handset on the base

facedown or faceup.

—

20 Channels

— automatically selects a clear

channel when you make or answer a call.

You can also manually change channels dur-

ing a call.

Features

ˆ Installation

Note:

The base's display is protected during

adapter from AC power before you dis-

connect it from the phone.

shipment by a piece of film. Carefully peel off

this film before using your phone for the first

time.

Your telephone connects directly to a modu-

lar telephone line jack. If your telephone wir-

ing does not have a modular jack, you can

update the wiring yourself using jacks and

adapters (available at your local RadioShack

store), or have the telephone company up-

date the wiring for you. You must use com-

patible modular jacks that are compliant with

Part 68 of FCC Rules.

MOUNTING THE PHONE

You can place the phone's base on a desk or

table, mount it on a standard wall plate, or

mount it directly on a wall.

Choose a location that is:

Note:

The USOC number of the jack to be

• near an AC outlet

installed is RJ11C (or RJ11W for a wall plate

jack).

• near a modular telephone line jack

• out of the way of normal activities

On a Desktop

• away from electrical machinery, electri-

cal appliances, metal walls or filing cabi-

nets, wireless intercoms, alarms, and

room monitors

1. Insert the bracket’s tabs into the base’s

upper tab slots, then press down on the

bracket’s clips and insert them into the

clip slots.

• away from other cordless phones

The base's location affects the phone's

range. If you have a choice of several loca-

tions, try each to see which provides the best

performance.

Cautions:

You must use a Class 2 power

source that supplies 9V AC

and delivers at least 350 mA.

Its center tip must be set to positive and

2. Plug one end of the supplied long modu-

TEL LINE

lar cord into the

jack on the

back of the base and route the cord

through the strain relief hook on the

bracket.

DC IN 9V

its plug must fit the phone's

jack. The supplied adapter meets these

specifications. Using an adapter that

does not meet these specifications

could damage the phone or the adapter.

3. Plug the modular cord’s other end into a

modular telephone line jack.

• Always connect the AC adapter to the

phone before you connect it to AC

power. When you finish, disconnect the

4. Insert the supplied AC adapter’s barrel

DC IN 9V

plug into the

the base.

jack on the back of

Installation

5. Route the adapter’s cord through the

strain relief slot on the bottom of the

bracket.

plate studs and slide the phone down-

ward to secure it.

6. Plug the adapter into a standard AC out-

let.

7. Lift the base’s antenna to a vertical posi-

tion.

On a Wall Plate or Wall

6. Plug the adapter into a standard AC out-

let.

1. Insert the bracket’s tabs into the base’s

lower tab slots, then press down on the

bracket’s clips and insert them into the

clip slots.

7. Lift the base’s antenna to a vertical posi-

tion.

Note:

To mount the phone directly on a wall,

you need two screws (not supplied) with

heads that fit into the keyhole slots on the

bottom of the base.

Follow the steps under “On a Wall Plate or

Wall,” then apply these additional instruc-

tions.

1. Drill two holes 3¹⁵/¹⁶inches (100 mm)

apart. Then thread a screw into each

2. Plug one end of the supplied short mod-

TEL LINE

ular cord into the

back of the base.

jack on the

hole, letting the heads extend about /⁸

inch (3 mm) from the wall.

3. Insert the supplied AC adapter’s barrel

2. Plug one end of the supplied long modu-

DC IN 9V

plug into the

jack.

TEL LINE

lar cord into the

jack on the

back of the base and route the adapter

cable and modular cords through the

grooves on the bracket.

4. Route the adapter cord through the

groove on the bracket.

5. Plug the modular cord’s other end into

the wall plate jack, then align the

bracket’s keyhole slots with the wall

3. Align the bracket’s keyhole slots with the

mounting screws and slide the phone

downward to secure it.

Installation

the handset to the base for about 5 sec-

onds.

CONNECTING, CHARGING,

AND REPLACING THE

BATTERY PACK

• Using a pencil eraser, clean the charg-

ing contacts on the handset and base

about once a month.

The phone comes with a rechargeable nick-

el-cadmium (Ni-Cd) battery pack in the hand-

set. Before using your phone, you must

connect the battery pack, then charge it for

about 24 hours.

• If the battery pack becomes weak during

a call, the handset beeps every 3 sec-

onds and Bemý8Wjj[ho flashes. When this

happens, you cannot make a call until

you recharge the battery pack.

1. Press down and slide off the battery

pack compartment cover.

• About once a month, fully discharge the

battery by keeping the handset off the

base until Bemý 8Wjj[ho flashes. Other-

wise, the battery pack loses its ability to

fully recharge.

2. Lift the battery pack out of the compart-

ment.

3. Plug the battery pack's connector into

the socket in the compartment, (the con-

nector fits only one way), replace the

battery pack, and replace the cover.

• If the display is blank and the phone

does not work, recharge the battery

pack. (The battery power might be too

low to light the display.)

To charge the battery pack, place the hand-

set either faceup or facedown on the base.

• If you are not going to use your phone

for an extended period of time, discon-

nect the battery pack. This increases the

battery pack's usable life.

The CHARGE/IN USE indicator on the base

lights and JejWb0&& appears.

Important:

Be sure the battery pack is prop-

erly connected before you try to charge it.

The CHARGE/IN USE indicator lights when

the handset is on the base even if the battery

pack is not properly connected.

The supplied battery pack should last about

a year. If the battery pack does not hold a

charge for more than 2 hours after an over-

night charge, replace it with a new 3.6-volt,

600 mAh battery pack with a connector that

fits the socket in the battery compartment.

You can order a replacement battery pack

through your local RadioShack store. Install

the new battery pack and charge it for about

24 hours.

Recharge the battery pack when Bemý8Wjj[ho

flashes.

Notes:

• When you first use the phone after

charging or recharging the battery pack,

the phone might not work and you might

Note:

To avoid losing information stored in

TALK

hear a beep when you press

memory, replace the battery within 2 min-

utes.

Return the handset to the base for about

5 seconds to reset the security access-

protection code.

Warning:

Dispose of the old battery pack

promptly and properly. Do not burn or bury it

(see “Battery Safety Instructions” on Page 5

for additional information on proper battery

handling).

• If the handset or the base loses power,

the security access-protection code

might be lost. To reset the code, return

Installation

If you have trouble replacing the battery

pack, take the phone to your local Ra-

dioShack store for assistance.

set to pulse mode or to set to tone mode.

The phone beeps and displays Fkbi[ý:_Wb_d]

or Jed[ý:_Wb_d], then the display clears.

Important:

Note:

The phone exits the setting mode if a

The EPA certified

RBRC^®Battery Recycling Seal

call or page is received, or if you press

on the handset or any key on the base.

TALK

on the nickel-cadmium (Ni-Cd)

battery indicates RadioShack

is voluntarily participating in an

SETTING THE RINGER

TONE/VOLUME

industry program to collect and recycle these

batteries at the end of their useful life, when

taken out of service in the United States or

Canada. The RBRC program provides a

convenient alternative to placing used Ni-Cd

batteries into the trash or the municipal

waste stream, which may be illegal in your

area. Please call 1-800-THE-SHACK (1-

800-843-7422) for information on Ni-Cd bat-

tery recycling and disposal bans/restrictions

in your area. RadioShack’s involvement in

this program is part of the company’s com-

mitment to preserving our environment and

conserving our natural resources.

You can select one of four different ringer

tone/volume settings on the handset. At any

time, except during a call or while reviewing

VOL/CID

Caller ID records, repeatedly press

8 or 9 to select the desired ringer setting.

Each time you press a button, the phone

rings at the selected setting and the display

shows H_d][h 7 >_]^, H_d][h 7 Bem, H_d][h 8

>_]^, or H_d][h 8 Bem.

You can also turn off the ringer. At any time,

except during a call, press and hold

VOL/CID

9 until the phone beeps and the display

shows H_d][h E\\. When you place the hand-

set face up on the base, 2H_d][hý E\\4 ap-

pears.

SETTING THE DIALING

MODE

Your phone comes set for tone dialing. If you

have pulse service, you need to change the

dialing mode. If you are not sure which type

of service you have, do this test.

You can still make or receive a call even

when the ringer is set to off. When you have

an incoming call, the phone connected to the

same line rings, and ?dYec_d] 9Wbb appears.

SPEAKER

Press

and listen for a dial tone.

VOL/

To turn the ringer back on, simply press

CID

Press any number other than .

8 or 9; the ringer is set to H_d][h 7 >_]^.

Note:

If your phone system requires that you

To set the base’s ringer volume, at any time

dial an access code (9, for example) before

you dial an outside number, do not press the

access code either.

RING

except during a call, repeatedly press

on the base until you get the desired setting

– H_d][hý >_]^, H_d][h Bem, or H_d][h E\\ ap-

pears. When you turn off the ringer. 2H_d][h

E\\4 remains on the display.

If the dial tone stops, you have touch-tone

service. If the dial tone continues, you have

pulse service.

Note:

When you set the base’s ringer off, the

base (and the handset if it is on the base)

does not ring but another phone connected

to the same line rings and ?dYec_d]ý9Wbb ap-

pears. If the handset is away from the base,

SPEAKER

To set the dial mode, press

hang up the phone if necessary, then hold

on the base until the phone

beeps andý:_WbýCeZ[0 and the current dialing

FLASH

down

mode, Jed[ or Fkbi[, appear. Then press to

Installation

the handset also rings (unless you set the

handset’s ringer to off).

With the Opt setting, you can use the ad-

vanced Caller ID/Call Waiting options. See

“Call Waiting Options Service” on Page 21.

TURNING AUTO TALK ON/

OFF

STORING YOUR AREA

CODE

Your phone is preset so you must press

TALK

when you lift the handset from the base

You can store your local area code in the

phone’s Caller ID record so it does not show

the area code if the received call is from your

local area. If for some reason you need to

dial the area code (or store in the memory),

you can add it afterwards. See “Adding/De-

leting the Area Code” on Page 23.

to answer a call. With auto talk turned on,

you can answer a call by just lifting the hand-

set from the base. If the handset is away

from the base, you can answer by pressing

any key.

Follow these steps to turn auto talk on or off.

Note:

If your calling area requires 10-digit di-

1. Lift the handset and press

. A

aling including area code, do not enter the

area code but leave this option blank.

menu appears with 7kje JWba selected.

SELECT/INTCM

2. Press

to change the auto

Follow these steps to store your area code.

talk setting. Ed or E\\ appears indicating

the selected setting.

1. Lift the handset and press

VOL/CID

9 twice to select

3. Return the handset to the base or press

2. Press

to store the new setting.

7h[W 9eZ[.

SELECT/INTCM

3. Press

, then enter your

TURNING CALLER ID/CALL

WAITING ON/OFF

three-digit area code. If you make a mis-

take, repeatedly press 6

7 to move the cursor over the

incorrect digit, then enter the correct

number.

REDIAL

FLASH

If you subscribe to Call Waiting with Caller ID

service, you can set the phone to show Call-

er ID information for an incoming call even

while you are using the phone.

Note:

If an area code is already stored,

it appears on the display. To delete the

Follow these steps to turn the Caller ID/Call

Waiting feature on or off.

DELETE/CH

area code, press

three

times. Then enter your area code. Or

REDIAL

FLASH

7 to

you can use 6

1. Lift the handset and press

. A

move the cursor and edit the area code.

menu appears with 7kje JWba selected.

SELECT/INTCM

4. Press

to store the area

or return the

VOL/CID

9 to select 9?:9M

2. Press or

code, then press

(Caller ID/Call Waiting).

handset to the base to clear the display.

SELECT/INTCM

3. Press

to change the

Caller ID/Call Waiting setting. Ed, E\\, or

Efj appears.

4. Press

then return the handset to

the base to store the new setting.

Installation

ˆ Operation

Note:

SPEAKER

To use the speakerphone, you must

To end a speakerphone call, press

again.

use the base keypad; to use the handset,

you must use the handset keypad.

RECEIVING A CALL

MAKING A CALL

When the phone receives a call, ?dYec_d] 9Wbb

appears. If you subscribe to Caller ID service

from your telephone company, the number

and name (if available) also appear.

Using the Handset

To make a call, lift the handset and press

TALK

. JWba and current volume setting appear

To answer the call using the handset, lift the

on the handset's display. >WdZi[j _d Ki[ ap-

pears on the base's display and CHARGE/IN

USE lights. Dial the number. You see the

number as you dial, then (after a few sec-

onds) the call's elapsed time.

TALK

handset off the base and press

. If auto

talk is on, just lift the handset or press any

key on the handset. To answer a call using

SPEAKER

the speakerphone, press

Note:

you press

You can also dial the number before

ADJUSTING THE VOLUME

TALK

. If you make a mistake, re-

To adjust the volume you hear through the

DELETE/CH

peatedly press

digit up to the wrong entry, then enter the

correct number. You can also press and hold

to erase each

VOL/CID

handset during a call, press

8 to

increase or 9 to decrease the volume. Leb#

kc[ CWn_ckc, Lebkc[ >_]^, Lebkc[ C[Z_kc,

or Lebkc[ Bemýappears.

DELETE/CH

for more than one second to de-

lete the entire number.

To adjust the speakerphone's volume, press

To end a call, place the handset on the base

VOL

8 or 9 on the base. The display

shows a bar graph of the volume level.

TALK

or press

Using the Speakerphone

Note:

If you press 8 while the volume is at

the maximum or press 9 while the volume

is low, the setting does not change and the

phone beeps three times.

To make or answer a call using the speaker-

SPEAKER

phone, simply press

. If[Wa[h ap-

pears on the base's display. Use the base's

keypad to dial the number. You see the num-

ber as you dial, then (after a few seconds)

the call's elapsed time.

SELECTING THE CHANNEL

The phone scans 20 channels (frequency

pairs used between the base and the hand-

set) and automatically selects a clear chan-

nel each time you make or receive a call. If

you hear other conversations or excessive

Note:

You can also dial the number before

SPEAKER

you press

. If you make a mistake,

MUTE/DELETE

repeatedly press

to erase

each digit up to the wrong entry, then enter

the correct number. You can also press and

DELETE/CH

noise during a call, press

to se-

lect a different channel. IYWdd_d] appears.

MUTE/DELETE

hold

for more than one sec-

ond to delete the entire number.

Note:

If the handset is too far from the base,

the channel might not change and you hear

Operation

an error beep. Move closer to the base and

try again.

conversation. 9

[

appears on the

base's display and CHARGE/IN USE lights.

During the call, one person can hang up and

let the call continue at the other keypad. Or,

both people can hang up to end the call.

USING MUTE

To talk to someone in the room while using

the speakerphone without the person on the

other end of the phone line hearing your con-

Note:

If you hear a high-pitched noise from

the base's speaker, the handset and the

base are too close together.

MUTE/DELETE

versation, press

on the base.

Ckj[ appears on the base's display.

MUTE/DELETE

Press

again to resume your

USING FLASH

phone conversation.

Flash performs the electronic equivalent of a

switchhook operation for special services,

such as Call Waiting. For example, if you

Note:

When you talk over the speakerphone,

the party that speaks first has priority. If you

are making a call in a noisy environment, the

phone might pick up the noise and assume

you are still communicating, thus not switch-

ing back to the person you are speaking with.

FLASH

have Call Waiting, press

to answer an

incoming call without disconnecting the cur-

FLASH

rent call. Press

first call.

again to return to the

MUTE/DELETE

If this should happen, press

Note:

services, pressing

the current call.

If you do not have any special phone

so the noise will not be picked up by the

FLASH

might disconnect

MUTE/DELETE

phone's microphone. Press

SPEAKER

to release when it is your turn to

speak.

USING REDIAL

SWITCHING BETWEEN THE

HANDSET AND THE

SPEAKERPHONE

To quickly dial any of the last three numbers

dialed on the handset, lift the handset and

REDIAL

press

. The last number dialed on the

RE-

handset appears below 2H[Z_Wbý'4. Press

To switch to the speakerphone while you are

DIAL

repeatedly until the desired number ap-

SPEAKER

using the handset, press

on the

TALK

pears on the display, then press

base. When you hear the conversation on

TALK

the speakerphone, press

set.

on the hand-

To dial the last number dialed on the base,

REDIAL/PAUSE

press

on the base. The last

number dialed on the base appears on the

To switch to the handset while you are using

the speakerphone, lift the handset off the

base. If the handset is away from the base,

SPEAKER

base's display. Then press

. You

can redial only the last number dialed on the

base.

TALK

SPEAKER

press

, then press

Notes:

USING BOTH THE HANDSET

AND THE SPEAKERPHONE

• The redial memory is separate for each

keypad. You cannot redial a number you

dialed on the handset keypad using

If someone else is using the speakerphone,

REDIAL

on the base, and vice versa.

TALK

press

on the handset to join the con-

versation. If someone else is using the hand-

SPEAKER

set, press

on the base to join the

Operation

• The redial memory holds up to 32 digits,

so you can redial any long-distance

number as well as local numbers.

In either case, if the called party does not an-

swer within 1 minute, the paging stops.

SELECT/INTCM

INTCM

again to re-

Press

start paging.

• The redial memory also holds pause

entries (see “Entering a Pause” on

Page 19).

TALK

To end an intercom call, press

on the

SPEAKER

handset, press

on the base, or

hang up the handset.

USING TONE SERVICES ON

A PULSE LINE

If a call comes in during an intercom conver-

sation, only the base rings (even if it is set to

Ringer Off), but the person at the handset

can also hear the ring through the intercom.

Either person can answer the call by press-

Some special services, such as bank-by-

phone, require tone signals. If you have

pulse service, you can still use these special

tone services.

TALK

SPEAKER

once to end the inter-

ing

TALK

SPEAKER

com call, then pressing

again to answer the call.

Dial the service’s main number. When the

TONE

service answers, press

/ . Any addi-

Note:

The intercom does not operate if the

tional numbers you dial are sent as tone sig-

nals.

party being paged is already on a call.

When you hang up, the phone automatically

resets to pulse dialing.

TRANSFERRING A CALL

BETWEEN THE HANDSET

AND THE BASE

USING PAGE/INTERCOM

You can use the phone's intercom feature to

transfer a call between the handset and the

base for a three-way conversation.

You can use the phone as a two-way pager

and intercom between the base and the

handset. This is useful if the handset is away

from the base and you want to locate it, or if

you want to converse with someone through

the intercom.

To transfer a call from the handset to the

SELECT/INTCM

base, press

. The call is

placed on hold, CHARGE/IN USE blinks and

>ebZ and FW]_d] appear at the base, and >ebZ

and FW]_d] 8Wi[ appear on the handset's dis-

play. When the person at the base answers

and the display changes to >ebZ and ?dj[hYec,

To page the base from the handset, press

SELECT/INTCM

. The base and handset ring.

FW]_d] appears on the base's display and

FW]_d] 8Wi[ appears on the handset's display.

TALK

press

. The call is released from hold

SPEAKER

INTCM

on the base to an-

Press

and transferred to the base. To bring the

handset back into the conversation for a

swer the page. Both displays change to ?dj[h#

Yec.

TALK

three-way conference, press

again.

IN-

To page the handset from the base, press

To transfer a call from the base to the hand-

TCM

. The handset and base ring. FW]_d]

INTCM

set, press

. The call is placed on hold,

>WdZi[j appears on the base's display and

FW]_d] appears on the handset's display.

CHARGE/IN USE blinks and >ebZ and FW]_d]

>WdZi[j appear at the base, and >ebZ and

FW]_d] appear on the handset’s display.

When the person with the handset answers

and the display changes to >ebZ and ?dj[hYec,

TALK

SELECT/INTCM

on the hand-

Press

set to answer the page. Both displays

change to ?dj[hYec.

Operation

SPEAKER

press

. The call is released from

handset. You can also make or answer calls

SPEAKER

button located on

hold and transferred to the handset and the

display changes to >WdZi[j _d Ki[. To bring

the base back into the conversation for a

by pressing the

the base.

You can use a handset holder (available

from your local RadioShack store) to hang

the handset on your belt for greater conve-

nience.

SPEAKER

three-way conference, press

again.

OUT OF RANGE

When you finish using the headset, discon-

nect it from the handset and close the rubber

cover to protect the jack.

If you have the handset out of the base's

range while a call is in progress, noise in-

creases. Return to the base’s range within

30 seconds, then you can resume your

phone conversation.

MEMORY DIALING

You can store up to 20 numbers in the hand-

set's memory and 10 in the base's memory,

then dial a stored number by pressing a

memory location number. You can also store

a name with each number in the handset's

memory.

If you keep the handset out of the base’s

range for 30 seconds or more, the call is dis-

connected. However if you are in 3-way con-

ference call, the speakerphone call remains

connected.

USING A HEADSET

Each number you store can be up to 20 dig-

its long, and each name can be up to 13

characters.

You can talk with handsfree convenience us-

ing an optional headset that has a /³²-inch

(2.5-mm) plug. Your local RadioShack store

has a variety of suitable headsets to chose

from.

You cannot dial a number stored in one

memory location (the base or the handset)

using the keypad on the other.

To connect the headset, open the rubber

cover on the side of the handset, then insert

the headset's plug into the jack.

Storing a Name and Number in the

Handset’s Memory

Notes:

When you are storing a number in memory,

the phone beeps and exits the storing pro-

cess if you wait more than 20 seconds be-

tween each keypress.

• Connecting a headset disconnects the

handset's earpiece and microphone.

VOL/CID

•

8 or 9 on the handset also

Note:

If you receive a call during memory en-

controls the connected headset's vol-

ume.

try, the phone exits the storing process.

• If you place the handset on the base to

recharge it while the headset is con-

nected, be sure the handset seats prop-

erly.

With a headset connected, you can make or

answer calls as usual using the keys on the

Operation

Follow these steps to store a number and

name in the handset.

next position, then press twice so 8

appears.

FLASH

7 twice

1. Lift the handset.

To enter a space, press

without entering any character.

MEM

2. Hold down

until C[cehoýIjeh[ and a

list of memory location numbers (and

names, if any) appear.

To enter a number, repeatedly press the

corresponding number key until the

number appears.

3. Select an empty memory location (or the

VOL/

one you want to replace) by using

To enter special character, use . Each

CID

8 or 9 to scroll through the list or

time you press , the following charac-

entering the location number (01–20).

Precede a single-digit number with a 0

(01, for example).

ters appear in this order:

# – & ( ) (space) 0

∗

REDIAL

If you make a mistake, use

FLASH

6or

7 to move the cursor over the

error, then enter the correct character, or

Note:

If the phone sounds five quick

beeps, you have made an entry error

and the number was not stored. Reenter

the location number correctly.

DELETE/CH

press

to delete a character.

To delete all characters, hold down

SELECT/INTCM

DELETE/CH

for at least 1 second.

4. Press

Ijeh[ DWc[

appears. If you do not want to enter a

name, skip to Step 6.

SELECT/INTCM

6. Press

Ijeh[ DkcX[h

appears.

5. To enter a name, use the number keys.

7. Enter the phone number and any tone or

pause entries (see “Entering a Pause”

on Page 19).

Refer to the letters on the number keys

to select the desired letter. Press the key

once for the first letter in the upper case,

press twice for the second letter in the

upper case, and so on. To enter the

lower case letter, press four times (or

five times) to display the first letter in

lower case, five or six times for the sec-

ond letter, and so on.

If you make a mistake, use the same

method to correct it as described in Step

SELECT/INTCM

8. Press

. The phone beeps

and C[cehodd Ijeh[Z (nn stands for the

memory location number you assigned)

appears. After 2 seconds, C[ceho Ijeh[

appears. Repeat Steps 3–8 to store

more numbers.

For example, to enter John: press

once; upper case @ appears. Then press

six times; lower case e appears. Press

five times; lower case ^ appears.

MEM

9. When you finish, press

Finally, press five times; lower case d

appears.

To replace a stored number, store a new one

in its place (see “Editing or Deleting a Num-

ber in the Handset's Memory” on Page 19).

To enter two letters from the same key in

a row, press

FLASH

7 to move the cur-

sor to the next position. For example to

enter AB, press ; 7 appears. Then

FLASH

press

7, the cursor moves to the

Operation

SELECT/

desired option then press

Storing a Number in the Base

INTCM

to choose it.

Follow these steps to store numbers in the

base:

Menu Options:

• ;Z_jý C[cehodd — edit the record as

described in Steps 5 through 8 of “Stor-

ing a Name and Number in the Hand-

set’s Memory” on Page 17.

MEMORY

1. Hold down

until Ijeh[ DkcX[h

appears on the base's display.

2. Enter the phone number and any tone or

pause entries (see “Entering a Pause”).

• :[b[j[ýC[cehodd — the display prompts

you to confirm the deletion. Move the

MEMORY

If you make a mistake, press

to exit the memory store operation. Start

again at Step 1.

SELECT/INTCM

cursor to O[i, then press

DELETE/CH

. The phone beeps, and

C[cehodd :[b[j[Z appears.

MEMORY

3. Press

again. I[b[Yj BeYWj_ed

appears. Enter the memory location

• =eý8WYa — returns you to the list of mem-

0 9

number ( – ) where you want to store

ory numbers.

the number. The phone beeps and

C[cehod Ijeh[Z appears.

Entering a Pause

To clear a stored number, simply store a new

In some telephone systems, you must dial an

access code (9, for example) and wait for a

second dial tone before you can dial an out-

side number. You can store the access code

with the phone number. However, you

should also store a pause after the access

code to allow the outside line time to con-

nect.

MEMORY

number in its place. Or, hold down

MEM-

until Ijeh[ DkcX[h appears. Then press

ORY

0 9

and the memory location number ( – )

you want to clear. The phone beeps and

C[cehodd :[b[j[Z appears.

Use the supplied memory directory sticker to

record your stored numbers. Peel the back-

ing from the sticker and attach it to the base.

REDIAL/

To enter a 2-second pause, press

PAUSE PAUSE

(

on the handset). F appears

Editing or Deleting a Number in

the Handset's Memory

when you enter a pause in the memory. You

can add more pause entries for a longer

pause.

Follow these steps to edit or delete a memo-

ry number.

1. Lift the handset.

MEM

2. Hold down

until C[ceho Ijeh[ and a

list of memory location numbers appear.

01 20

) by

3. Choose a memory location (

–

pressing a number or by repeatedly

VOL/CID

pressing

8 or 9.

SELECT/INTCM

4. Press

. A menu appears

with the three options listed below.

VOL/CID

Press

8 or 9 to highlight the

Operation

To dial a number stored in the base's memo-

Reviewing Memory Numbers

Handset

MEMORY

ry, press

. I[b[Yj BeYWj_ed appears.

0 9

Press a number key ( – ); the display shows

the number contained in the selected memo-

To review your memory numbers stored in

SPEAKER

ry location. Press

ber on the display.

to dial the num-

MEM

the handset, press

. The list of memory

location numbers (&'–(&) and the name

stored with each number (orý2C[cehodd4 if

you did not store a name) appears. To view a

Note:

If you select an empty memory loca-

tion, no number appears.

01 20

– ) or

memory location, press its number (

VOL/CID

repeatedly press

8 or 9.

Chain-Dialing Service Numbers

To see the stored phone numbers, press

For quick recall of numbers for special ser-

vices (such as bank by phone), store each

group of numbers in its own memory loca-

tion. Dial the service's main number first.

Then, at the appropriate place in the call,

FLASH

7. An arrow to the right of the num-

ber means it is longer than 14 digits. Press

FLASH

7 again to see the rest of the num-

ber.

MEM

MEMORY

on the base) and en-

press

(or

REDIAL

Repeatedly press 6

name display.

to return to the

ter the number for the location where the ad-

ditional information is stored.

MEM

To exit the memory number list, press

Testing Stored

Emergency Numbers

To see a stored name and phone number at

SELECT/INTCM

the same time, press

when

the cursor is by a memory location number.

If you store an emergency service's number

(police department, fire department, ambu-

lance) and you choose to test the stored

number, make the test call during the late

evening or early morning hours to avoid peak

demand periods. Also, remain on the line to

explain the reason for your call.

DELETE/CH

To exit this display, hold down

until the display clears.

Base

To review your memory numbers stored in

MEMORY

the base, press

. I[b[Yj BeYWj_ed ap-

0 9

pears. Press a memory location number –

to review the number you have stored.

Dialing a Memory Number

To dial a number stored in handset's memo-

MEM

ry, lift the handset and press

. The list of

memory location numbers appears. Choose

01 20

– ) by pressing a

a memory location (

VOL/CID

number or by repeatedly pressing

TALK

8 or 9, then press

You can also dial a memory number after

TALK

MEM

(the display does

pressing

. Press

not change but the phone is in memory recall

mode) then enter a memory location number.

Operation

ˆ Caller ID Operation

If you subscribe to Caller ID service from

your phone company, the phone company

sends information about the call, as well as

the time and date, between the first and sec-

ond rings of every call you receive. This in-

formation appears after the second ring on

both the handset's and the base's displays.

The display also shows if caller information is

unavailable or if the name and number were

blocked by the caller (see “Caller ID Messag-

es” on Page 23).

mail, or answer the second caller with a pre-

recorded message asking them to hold the

line.

Before you can use the Call Waiting Options

Services, you must:

• subscribe to the Options service from

your telephone company.

• set the Caller ID/Call Waiting feature to

Opt (see “Turning Caller ID/Call Waiting

On/Off” on Page 13).

If you subscribe to Call Waiting with Caller

ID, you will hear a tone through the handset

when a call comes in, then the Caller ID

record appears. If you want to answer the in-

Using Call Waiting Options

Note:

The phone beeps five times and exits

FLASH

coming call, press

. To resume the

the menu mode if you wait more than 20 sec-

onds between each keypress.

FLASH

previous phone conversation, press

again.

You hear a soft beep when a call comes in

while you are already on the phone. The dis-

play shows the caller name and phone num-

ber.

The handset has Caller ID memory to store

the information received for up to 50 Caller

ID records for later review. It stores the infor-

mation even when you answer the call using

the speakerphone.

When you see a Caller ID/Call Waiting dis-

play, follow these steps to use Call Waiting

Options Services.

If the Caller ID memory becomes full, any

new call replaces the oldest call's record.

1. Press

. A list of several options,

The base's NEW CALL indicator also flashes

when the phone receives a call with Caller ID

information and you have not yet reviewed it.

Use the handset's Caller ID memory to re-

view the information about the calls received.

beginning with 7ia je >ebZ appears.

VOL/CID

2. Repeatedly press

9 to scroll

through the options list. You can also

press the number of the desired option.

3. Choose one of the following options,

CALL WAITING OPTIONS

SERVICE

SELECT/INTCM

then press

7iaý jeý >ebZ — A waiting caller hears a

prerecorded message stating that you

will be available shortly, and is put on

hold. 9Wbb >ebZ_d] appears on your phone.

You can order Call Waiting Options Service

from your phone company. This service pro-

vides you with more choices on how to han-

dle a second call when you are already on

the phone. You can switch between the call-

ers, have a 3-way conference call with both

callers, send the second caller to your voice

J[bbý8kio — A prerecorded message indi-

cates you are busy, and the waiting call

Caller ID Operation

is disconnected. J

appears on

Press

SELECT/INTCM

your phone.

2. If you decide to take the second call,

JWa[ C[iiW][ — Send a waiting caller to

your phone company’s voice mail ser-

vice. Je Le_Y[ CW_b appears on your

phone.

and end the first, scroll down to 7dim[h%

:hef ' or press .

SELECT/INTCM

Press

3. If you decide to include the second

caller in your conversation with the first

caller, scroll down to 9ed\[h[dY[ or press

Note:

Voice Mail is a service available

from some telephone companies. A call

for a subscriber can be kept at the tele-

phone company and retrieved later on

by calling the special number and enter-

ing the caller’s phone number and code

number. Check with your telephone

company to determine if this service is

available.

SELECT/INTCM

Press

Using Conference

You can either begin a conference call as

soon as you receive a second call, or after

the second caller has been on hold for a

while (see “Using Ask to Hold”).

7dim[h%:hef ' — Disconnects the first

call, and connects automatically to the

new caller. 7dim[h%:hef 'ij appears.

Once you have established a conference

call, you can end it at any time by dropping

one of the calls.

9ed\[h[dY[ — Allows you to speak with

your first and second callers to have a 3-

way conference call. 9ed\[h[dY[Z

appears.

:hef <_hij — hang up on the first caller and

continue with the second.

:hefý<_hij and :hefýBWij are options you

can only use with a conference call (see

“Using Conference”). 9Wbb :heff[Z

appears.

:hef BWij — hang up on the second caller

and continue with the first.

Follow these steps to drop one of the calls.

Using Ask to Hold

1. To end a conference call, press

When you select 7ia je >ebZ, you can then

use several of the other options as well.

2. Scroll down to :hef <_hij (or press ) or

:hef BWij (or press ) to drop the desired

call.

1. If you decide you cannot end your first

call, and you do not want to continue to

leave the second call on hold, press

SELECT/INTCM

3. Press

9Wbb :heff[Z

appears.

To notify the second caller that you are

busy, scroll down to J[bb 8kio or press .

To send the second caller to voice mail

(if you have voice mail), scroll down to

JWa[ C[iiW][ or press .

Caller ID Operation

REVIEWING CALLER ID

RECORDS

Display

Description

The caller is not within a

Caller ID service area.

KdademdýDWc[

(Handset Only)

Kdademd DkcX[h

To review the Caller ID records in the hand-

set's memory, lift the handset and press CID.

The number of new Caller ID records, if any,

and the total number of records appears.

?dYecfb[j[ :WjW

Appears if there was an

error during the transmis-

sion of Caller ID informa-

tion. Minor electrical

disturbances can affect

Caller ID information. Occa-

sional errors are normal. If

the phone frequently dis-

plays ?dYecfb[j[ :WjW, con-

tact your local telephone

company or RadioShack

store for assistance.

Note:

If the handset is faceup on the base, it

shows the number of Caller ID records, so

you can see if you have new records to re-

view.

VOL/CID

Repeatedly press

through the Caller ID records from the new-

9 to scroll

VOL/CID

est to the oldest, or

8 to scroll back

through the records. To scroll quickly through

ADDING/DELETING THE

AREA CODE

VOL/CID

the records, hold down

8 or 9.

When you scroll past the last record, total

record number appears, then the first record.

When you scroll past the first record, the total

record number appears, then the last record.

(Handset Only)

When the area code of the received call is

the same as the one you stored (see “Storing

Your Area Code” on Page 13), the caller ID

record does not show the area code. If it is

different, the record shows the area code.

However, you can add or delete the area

code on the display. When the record is on

The top line of each record shows the date,

time and the number of calls from that num-

ber. The second line shows the caller's

name, and the third line shows the caller's

phone number.

the display, press to add or delete the area

code. Pressing again deletes or adds the

area code.

Note:

the base.

Calls cannot be reviewed or stored in

When you dial the number or store it into

memory, the phone dials or stores the num-

ber as it appears on the display.

Caller ID Messages

Display

Description

DIALING NUMBERS FROM A

CALLER ID RECORD

Shows the number of new

Caller ID records ( records

you have not reviewed) and

the total number of records.

D[m0ýNN

JejWb0ýNN

(Handset Only)

To dial a local number stored in a Caller ID

Fh_lWj[ DWc[

Fh_lWj[ DkcX[h

The caller has blocked the

Caller ID information from

being sent.

TALK

record, recall the record, then press

. If

it is a long distance call, press (' appears

before the displayed number) before you

TALK

press

. If you want to add or delete the

TALK

area code, press before you press

Caller ID Operation

Note:

If a Caller ID record does not contain a

Follow these steps to delete a single Caller

ID record.

phone number (if it was blocked by the caller,

for example) you cannot dial from that

record.

CID

VOL/CID

8 or 9 to

1. Press

then

recall the record you want to delete.

STORING A CALLER ID

RECORD TO MEMORY

DELETE/CH

2. Press

:[b[j[ C[iiW][5

appears, prompting you to confirm the

deletion.

(Handset Only)

VOL/CID

3. Press

8 to move the cursor to

Follow these steps to store the name and

number from a Caller ID record into a memo-

ry location.

SELECT/INTCM

O[i, then press

DELETE/CH

. The phone beeps once

indicating that the record was deleted.

CID

VOL/CID

8 or 9 to

1. Press

then

Follow these steps to delete all Caller ID

records.

recall the record you want to store.

If it is a long distance number, press .

CID

1. Press

so the record totals appear.

If you want to add or delete the area

DELETE/CH

2. Press

. :[b[j[ý 7bb5 appears,

code, press .

prompting you to confirm the deletion.

MEM

2. Press

. I[b[Yj BeYWj_ed appears.

VOL/CID

3. Press

8 to move the cursor to

SELECT/INTCM

O[i, then press

DELETE/CH

. The phone beeps once and

JejWb0&& appears.

01 20

) by

3. Choose a memory location (

–

pressing a number or by repeatedly

VOL/CID

pressing

8 or 9, then press

SELECT/INTCM

If the selected location is empty, the

phone beeps to confirm that it stored the

number, then the Caller ID record

appears.

If a record exists in the selected loca-

tion, H[fbWY[ýC[ceho5 appears, prompt-

ing you to confirm the replacement.

Move the cursor to O[i or De, then press

SELECT/INTCM

DELETING CALLER ID

RECORDS

(Handset Only)

You can delete Caller ID records individually

or all at once.

Caller ID Operation

ˆ Troubleshooting

We do not expect you to have any problems with your phone, but if you do, these suggestions

might help.

Problem

Suggestion

Low volume or unusual sounds.

Someone has picked up another phone on the same line.

Hang up the other phone.

DELETE/CH

to change the channel.

Severe noise interference.

Press

Keep the handset away from computers, remote control

toys, wireless microphones, alarm systems, intercoms,

room monitors, fluorescent lights, and electrical appli-

ances.

Move the handset to another location or turn off the

source of interference.

The phone cannot be operated at a useful

distance from the base because the signal

becomes weak or noisy (handset's range

has decreased).

Lift the base's antenna to a vertical position.

Be sure neither antenna is touching a metal surface.

Return the handset to the cradle, and recharge the battery

pack.

Replace the battery pack if necessary.

The phone does not work or works poorly.

The handset battery pack does not charge.

Be sure the base's phone line cord and AC adapter are

correctly and securely connected, and the battery pack is

charged.

Check the charging contacts on the handset and base. If

they are dirty, clean them with a pencil eraser.

Be sure the battery pack is connected correctly.

Replace the battery pack (see “Connecting, Charging,

and Replacing the Battery Pack” on Page 11).

The handset does not ring or receive a

page.

Be sure the handset ringer is not set to Ringer Off.

Move the handset closer to the base.

Be sure the battery pack is charged. (If the battery power

is too low, it does not have enough power to light the dis-

play.)

Troubleshooting

Problem

Suggestion

The handset stops working or works poorly

during a call.

Move the base away from other electrical devices and

sources of noise.

Move the handset closer to the base.

Lift the base's antenna to a vertical position.

Be sure the battery pack is charged. (If the battery power

is too low, it does not have enough power to light the dis-

play.)

If the base loses power while the handset is away, the

security access-protection code might change. Restore

power to the base, then place the handset back on the

base. The CHARGE/IN USE indicator lights, indicating

that the code is set again.

Check the charging contacts on the handset and base. If

they are dirty, clean them with a pencil eraser.

You have an incoming call, but do not

receive any Caller ID information.

Let the phone ring twice before you answer so the system

has time to record the Caller ID information.

Check that the system is correctly and securely con-

nected.

Call your phone company to verify that your Caller ID ser-

vice is active.

Cannot receive Caller ID/Call Waiting infor-

mation.

Check that the Caller ID/Call Waiting setting is set to Ed or

Efj.

If you still have problems, disconnect the phone. If other phones on the same line work proper-

ly, the fault is in this phone or its installation. If you cannot find the problem, take your phone to

your local RadioShack store for assistance.

connect your phone until you have resolved

CARE

the problem.

Keep the phone dry. If it gets wet, wipe it dry

immediately. Use and store the phone only in

normal temperature environments. Handle

the phone gently and carefully. Do not drop

it. Keep the phone away from dust and dirt.

Wipe the phone with a damp cloth occasion-

ally to keep it looking new.

Modifying or tampering with the phone’s in-

ternal components can cause a malfunction

and might invalidate its warranty and void

your FCC authorization to operate it. If your

phone is not performing as it should, take it

to your local RadioShack store for assis-

tance. If the trouble is affecting the telephone

lines, the phone company can ask you to dis-

Troubleshooting

ˆ Notes

Notes

Limited One-Year Warranty

This product is warranted by RadioShack against manufacturing defects in material and workman-

ship under normal use for one (1) year from the date of purchase from RadioShack company-owned

stores and authorized RadioShack franchisees and dealers. EXCEPT AS PROVIDED HEREIN, Ra-

dioShack MAKES NO EXPRESS WARRANTIES AND ANY IMPLIED WARRANTIES, INCLUDING

THOSE OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED

IN DURATION TO THE DURATION OF THE WRITTEN LIMITED WARRANTIES CONTAINED

HEREIN. EXCEPT AS PROVIDED HEREIN, RadioShack SHALL HAVE NO LIABILITY OR RE-

SPONSIBILITY TO CUSTOMER OR ANY OTHER PERSON OR ENTITY WITH RESPECT TO ANY

LIABILITY, LOSS OR DAMAGE CAUSED DIRECTLY OR INDIRECTLY BY USE OR PERFOR-

MANCE OF THE PRODUCT OR ARISING OUT OF ANY BREACH OF THIS WARRANTY, IN-

CLUDING, BUT NOT LIMITED TO, ANY DAMAGES RESULTING FROM INCONVENIENCE, LOSS

OF TIME, DATA, PROPERTY, REVENUE, OR PROFIT OR ANY INDIRECT, SPECIAL, INCIDEN-

TAL, OR CONSEQUENTIAL DAMAGES, EVEN IF RadioShack HAS BEEN ADVISED OF THE

POSSIBILITY OF SUCH DAMAGES.

Some states do not allow limitations on how long an implied warranty lasts or the exclusion or limita-

tion of incidental or consequential damages, so the above limitations or exclusions may not apply to

you.

In the event of a product defect during the warranty period, take the product and the RadioShack

sales receipt as proof of purchase date to any RadioShack store. RadioShack will, at its option, un-

less otherwise provided by law: (a) correct the defect by product repair without charge for parts and

labor; (b) replace the product with one of the same or similar design; or (c) refund the purchase

price. All replaced parts and products, and products on which a refund is made, become the prop-

erty of RadioShack. New or reconditioned parts and products may be used in the performance of

warranty service. Repaired or replaced parts and products are warranted for the remainder of the

original warranty period. You will be charged for repair or replacement of the product made after the

expiration of the warranty period.

This warranty does not cover: (a) damage or failure caused by or attributable to acts of God, abuse,

accident, misuse, improper or abnormal usage, failure to follow instructions, improper installation or

maintenance, alteration, lightning or other incidence of excess voltage or current; (b) any repairs

other than those provided by a RadioShack Authorized Service Facility; (c) consumables such as

fuses or batteries; (d) cosmetic damage; (e) transportation, shipping or insurance costs; or (f) costs

of product removal, installation, set-up service adjustment or reinstallation.

This warranty gives you specific legal rights, and you may also have other rights which vary from

state to state.

RadioShack Customer Relations, 200 Taylor Street, 6th Floor, Fort Worth, TX 76102

We Service What We Sell

12/99

43-3516

UCZZ01744ZZ

07A01

Printed in China

RadioShack Corporation

Fort Worth, Texas 76102

Quadra Fire Electric Heater GARNET D CSB User Guide
RCA Flat Panel Television HD56W41 User Guide
Ricoh All in One Printer MP 1100 User Guide
Russell Hobbs Dishwasher RHDW1 User Guide
Samsung Camcorder W300 User Guide
Samsung Flat Panel Television HP S6373 User Guide
Samsung Range NE597N0PBSR User Guide
Sanus Systems Cell Phone NF203 User Guide
Sanyo Cell Phone S750i User Guide
Sennheiser Headphones HD 457 User Guide